电子发烧友App

硬声App

0
  • 聊天消息
  • 系统消息
  • 评论与回复
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心

完善资料让更多小伙伴认识你,还能领取20积分哦,立即完善>

3天内不再提示
创作
电子发烧友网>电子资料下载>类型>参考设计>Quad-MxFE校准板用户指南

Quad-MxFE校准板用户指南

2021-03-22 | pdf | 7.51MB | 次下载 | 免费

资料介绍

This version (04 Feb 2021 21:28) was approved by Mike Jones.The Previously approved version (04 Feb 2021 21:24) is available.Diff

Calibration Board

Splitter/Combiner, Calibration, Power Analyzer

Features

  • Mates to Quad-MxFE Digitizing Card & VCU118 PMOD Interface (Cable Included)
  • MATLAB Control Enables System-Level Calibration Algorithm Development
  • Provides Both Individual Adjacent Channel Loopback and Combined Channel Loopback Options
  • Combined Tx Channels Out Via SMA Option
  • Combined Rx Channels In Via SMA Option
  • On-Board Log Power Detectors With AD5592R Output To VCU118 Over PMOD
  • On-Board Power Regulation from Single 12V Power Adapter (Included)

Below is the full integrated system including the Xilinx VCU118, ADQUADMXFE1EBZ, and ADQUADMXFE-CAL in full operation. For LED identification please see Calibration Broad LED Information, or Quad MxFE LED Information


General Description

This page serves to inform system engineers and software developers about the calibration board addition kit that pairs with the Quad-MxFE. This board directly aligns with the 16 Rx and 16 Tx ports on the output of the Quad MxFE and includes power detectors and loopback configurations for the system-level calibration of the Quad MxFE. The board contains a PMOD 2A interface that connects the VCU118 Evaluation Board from Xilinx®. A DIP switch and multi-channel ADC/DAC,AD5592R, are also included for additional control and power readings. The goal of this kit is to enable users to demonstrate combined-channel dynamic range, spurious, and phase noise improvements, develop system-level calibration algorithms, and demonstrate immediate phase determinism.

High Level Block Diagram

Key Component Location

LED Identification

LED Status Indicators
LED Ref Des Function
DS601 1.9V @ 1.2mA Good From ADM7150 (LDO)
DS602 1.9V @ 1.2mA Good From ADM7150 (LDO)
DS603 3.3V_FPGA Good From VCU118 PMOD 2A

Equipment Needed


Control Interfaces

The calibration board can be controlled in multiple ways including a DIP Switch and 2A PMOD Interface. The board can be controlled with 4 main signals: 5045 V1 and 5045 V2 which control an ADRF5045 which switches the transmit path between combined loopback, low frequency path, high frequency path, and power detection path, CTLR IND which turns off and on adjacent individual loopback for each Rx and Tx channel, and CTRL RX COMB which turns off and on the combined receive loopback path. The DIP Switch controls 4 signals: 5045 V1, 5045 V2, CTRL IND, and CTRL RX COMB. The PMOD Interface has 8 signals: 5045 V1, 5045 V2, CTRL IND, CTRL RX COMB, and 4 SPI Communications signals. The AD5592R is an 8 channel GPIO/ADC/DAC and it is connected the same control signals as the DIP switch as well as the three power detectors (AD8318, HMC948, LTC5596), plus a temperature sensor on the AD8318. Below is a tabular representation of these control signals.

Software Needed

The following link contains the MATLAB driver for controlling the 16 Tx / 16 Rx Calibration board via the VCU118 PMOD interface. The driver may be used to configure the Quad MxFE platform in a Combined Loopback, Individual Loopback, Combined Tx to SMA, Combined Rx from SMA, Combined Tx Power reading, and Power readings from the AD5592R and subsequent (AD8318, HMC948, LTC5596).

  • AD5592R 8 Channel, 12-Bit, Configurable ADC/DAC with on-chip Reference, SPI interface
  • HMC948 54 dB Logarithmic Detector SMT, 1 - 23 GHz
  • LTM5596 100MHz to 40GHz Linear-in-dB RMS Power Detector with 35dB Dynamic Range
  • AD8318 1 MHz TO 8 GHz, 70 dB Logarithmic Detector/Controller
  • ADP5020 Power Management Unit for Imaging Modules
  • AD5045 Fully Accurate 14-Bit VOUT nanoDAC® SPI Interface 4.5 V to 5.5 V in a TSSOP

Schematic

下载该资料的人也在下载 下载该资料的人还在阅读
更多 >

评论

查看更多

下载排行

本周

  1. 1电子电路原理第七版PDF电子教材免费下载
  2. 0.00 MB  |  1491次下载  |  免费
  3. 2单片机典型实例介绍
  4. 18.19 MB  |  95次下载  |  1 积分
  5. 3S7-200PLC编程实例详细资料
  6. 1.17 MB  |  27次下载  |  1 积分
  7. 4笔记本电脑主板的元件识别和讲解说明
  8. 4.28 MB  |  18次下载  |  4 积分
  9. 5开关电源原理及各功能电路详解
  10. 0.38 MB  |  11次下载  |  免费
  11. 6100W短波放大电路图
  12. 0.05 MB  |  4次下载  |  3 积分
  13. 7基于单片机和 SG3525的程控开关电源设计
  14. 0.23 MB  |  4次下载  |  免费
  15. 8基于AT89C2051/4051单片机编程器的实验
  16. 0.11 MB  |  4次下载  |  免费

本月

  1. 1OrCAD10.5下载OrCAD10.5中文版软件
  2. 0.00 MB  |  234313次下载  |  免费
  3. 2PADS 9.0 2009最新版 -下载
  4. 0.00 MB  |  66304次下载  |  免费
  5. 3protel99下载protel99软件下载(中文版)
  6. 0.00 MB  |  51209次下载  |  免费
  7. 4LabView 8.0 专业版下载 (3CD完整版)
  8. 0.00 MB  |  51043次下载  |  免费
  9. 5555集成电路应用800例(新编版)
  10. 0.00 MB  |  33562次下载  |  免费
  11. 6接口电路图大全
  12. 未知  |  30320次下载  |  免费
  13. 7Multisim 10下载Multisim 10 中文版
  14. 0.00 MB  |  28588次下载  |  免费
  15. 8开关电源设计实例指南
  16. 未知  |  21539次下载  |  免费

总榜

  1. 1matlab软件下载入口
  2. 未知  |  935053次下载  |  免费
  3. 2protel99se软件下载(可英文版转中文版)
  4. 78.1 MB  |  537793次下载  |  免费
  5. 3MATLAB 7.1 下载 (含软件介绍)
  6. 未知  |  420026次下载  |  免费
  7. 4OrCAD10.5下载OrCAD10.5中文版软件
  8. 0.00 MB  |  234313次下载  |  免费
  9. 5Altium DXP2002下载入口
  10. 未知  |  233046次下载  |  免费
  11. 6电路仿真软件multisim 10.0免费下载
  12. 340992  |  191183次下载  |  免费
  13. 7十天学会AVR单片机与C语言视频教程 下载
  14. 158M  |  183277次下载  |  免费
  15. 8proe5.0野火版下载(中文版免费下载)
  16. 未知  |  138039次下载  |  免费