资料介绍
Table of Contents
ADIS1650x-x/PCBZ BREAKOUT BOARD WIKI GUIDE
OVERVIEW
There are seven (7) breakout boards that support ADIS1650x IMU products. These breakout boards that provide a simple way to develop a prototype connection between the ADIS1650x IMUs and an existing embedded processor platform. This breakout board already contains the ADIS1650x IMU and one 16-pin header, which mates to 2 mm ribbon cables. As a general guideline, these breakout boards will support reliable communications over ribbon cables that are up to 20 cm in length, but it is always a good idea to validate signal integrity before relying on this type of connection to support a critical communication link.
PART NUMBER SUMMARY
Please see the follow table for a list of available breakout boards, along with the IMU model number that is on each board.
MODEL NUMBERS | MEASUREMENT RANGE | ||
---|---|---|---|
BREAKOUT BOARD | IMU | GYROSCOPE | ACCELEROMETER |
ADIS16500/PCBZ | ADIS16500AMLZ | +/-2000 dps | +/-40g |
ADIS16505-1/PCBZ | ADIS16505-1BMLZ | +/-125 dps | +/-8g |
ADIS16505-2/PCBZ | ADIS16505-2BMLZ | +/-500 dps | +/-8g |
ADIS16505-3/PCBZ | ADIS16505-3BMLZ | +/-2000 dps | +/-8g |
ADIS16507-1/PCBZ | ADIS16507-1BMLZ | +/-125 dps | +/-40g |
ADIS16507-2/PCBZ | ADIS16507-2BMLZ | +/-500 dps | +/-40g |
ADIS16507-3/PCBZ | ADIS16507-3BMLZ | +/-2000 dps | +/-40g |
The primary attributes that differentiate each of these models are measurement range (gyroscopes and accelerometers) and the calibration temperature range.
EVAL-ADIS2 CONNECTION
The J1 connector on each ADIS1650x-x/PCBZ breakout board is pin-for-pin compatible with the same connector (J1) on the EVAL-ADIS2 evaluation system. The picture below shows the EVAL-ADIS2 connectors.
If connecting an external power supply, refer to the picture below for the polarity of the J3 external power connector:
The user should follow these steps when connecting the xxx to the EVAL-ADIS2 evaluation system:
1. Ensure that Jumper JP1 is straddling the left “+3.3V REG” pin and the center pin, assuming the EVAL-ADIS2 board is oriented with the Mini-USB connector is on the left-hand side.
Note: If the user wishes to use an external power supply, move the JP1 jumper so that it straddles the center and lower pin and connect the external supply to Connector J3. GND is the left pin and VDD (+3.3 V) is the right pin.
2. Connect the ribbon cable between the EVAL-ADIS2 and ADIS1650x-x evaluation board.
3. Install the SDP Drivers from EVAL-ADIS2 USB Drivers.
3. Install the ADIS-EVAL2 Evaluation software from EVAL-ADIS2 Evaluation Software
4. Connect the EVAL-ADIS2 USB cable to the PC and verify that LED1 and LED2 are illuminated on the EVAL-ADIS2 board.
5. More information regarding the EVAL-ADIS2 evaluation system can be found at: EVAL-ADIS2 Wiki Guide
6. More information regarding the operation of the evaluation software can be found at: adis1650x_evalguide_pr.c.pdf
DIMENSTIONS/MOUNTING HOLES
These breakout boards have four mounting holes (one in each corner) which support attachment to another surface with M2 machine screws. Please see the following diagram for more details:
INTERFACE CONNECTOR
Please see the following table for the pin assignments for the interface connector (J1)
PIN | NAME | DESCRIPTION |
---|---|---|
1 | ~RST | Reset, Active Low |
2 | SCLK | Serial Clock (Serial Peripheral Interface) |
3 | ~CS | Chip Select (Serial Peripheral Interface), Active Low |
4 | DOUT | Data Output (Serial Peripheral Interface) |
5 | DNC | Do not connect |
6 | DIN | Data Input (Serial Peripheral Interface) |
7 | GND | Ground |
8 | GND | Ground |
9 | GND | Ground |
10 | VDD | Power Supply, +3.3V |
11 | VDD | Power Supply, +3.3V |
12 | VDD | Power Supply, +3.3V |
13 | DR | Data Ready |
14 | SYNC | Sync Input |
15 | DNC | Do not connect |
16 | DNC | Do not connect |
CABLING
J1 supports connection with the following style of cables: 2.00 mm IDC Ribbon Cable Assembly
TIP: Use “2.00 mm IDC Ribbon Cable Assembly” as search criteria to find the latest options on the market.
At the time of initial release for these breakout boards, we were most familiar with the TCSD Series from Samtec.
ELECTRICAL SCHEMATIC
The following diagram illustrates the electrical schematic for the ADIS16500/PCBZ. Please note that the only difference in the other models will be in the IMU (ADIS16470AMLZ is shown in the following view). Click on this image to access a higher-resolution view.
REFERENCE DESIGNS & CODE EXAMPLES
This section provides a list of reference designs for those who are ready to evaluate the ADIS1650x. These references designs include one or both of the following:
- The physical connection between the ADIS1647x-x/PCB and a specific embedded processor platform/system
- Embedded code that lists all ADIS1650x user registers, manages the ADIS1650x's SPI protocol requirements, and provides examples for accessing the ADIS1650x's registers
- 基于ADIS1620x/PCBZ加速计的
- ADIS1613x评估工具订购指南
- ADIS16448/PCBZ数据表
- ADIS16405/PCBZ数据表
- ADIS16260/ADIS16265/PCBZ数据表
- ADIS16300/PCBZ数据表
- ADIS16220/PCBZ数据表
- ADIS16IMU2/PCBZ Wiki指南
- CN0416-用户指南Wiki
- ADIS1650x 3D设计模型
- ADIS1646x/ADIS1647x/ADIS1650x Linux设备漂流器
- ADIS1650x 3D Design Model
- 基于ADIS16203/PCBZ加速计的参考设计
- 基于ADIS16201/PCBZ加速计的参考设计
- 基于ADIS16209/PCBZ加速计的参考设计
- X-RAY检测设备操作指南 386次阅读
- 电工必备接线指南:轻松掌握各种电路接线技巧 805次阅读
- 滤波器设计指南 2096次阅读
- 如何设置搭载最新的AMD锐龙9 7950X3D或锐龙9 7900X3D处理器的系统? 1285次阅读
- T3和E3网络接口布局指南 1899次阅读
- Azure主机操作系统–云主机 726次阅读
- 使用X-微波对射频设计进行原型设计的更好方法 772次阅读
- 为什么电子指南针能指示方向 1629次阅读
- PCB设计之五个EMI设计指南 3397次阅读
- firefly AIO-3288J主板使用指南 1510次阅读
- X射线探伤是什么意思_X射线探伤的原理 1.1w次阅读
- DS3231+TM1650制作4位0.56寸数码管迷你时钟 1.3w次阅读
- 美国模拟器件公司ADI推出了一款多轴运动传感器ADIS16355 1858次阅读
- iPhone自带的指南针的妙用 7562次阅读
- ADIS16355芯片MEMS陀螺仪数据采集硬件设计 5960次阅读
下载排行
本周
- 1电子电路原理第七版PDF电子教材免费下载
- 0.00 MB | 1491次下载 | 免费
- 2单片机典型实例介绍
- 18.19 MB | 95次下载 | 1 积分
- 3S7-200PLC编程实例详细资料
- 1.17 MB | 27次下载 | 1 积分
- 4笔记本电脑主板的元件识别和讲解说明
- 4.28 MB | 18次下载 | 4 积分
- 5开关电源原理及各功能电路详解
- 0.38 MB | 11次下载 | 免费
- 6100W短波放大电路图
- 0.05 MB | 4次下载 | 3 积分
- 7基于单片机和 SG3525的程控开关电源设计
- 0.23 MB | 4次下载 | 免费
- 8基于AT89C2051/4051单片机编程器的实验
- 0.11 MB | 4次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 2PADS 9.0 2009最新版 -下载
- 0.00 MB | 66304次下载 | 免费
- 3protel99下载protel99软件下载(中文版)
- 0.00 MB | 51209次下载 | 免费
- 4LabView 8.0 专业版下载 (3CD完整版)
- 0.00 MB | 51043次下载 | 免费
- 5555集成电路应用800例(新编版)
- 0.00 MB | 33562次下载 | 免费
- 6接口电路图大全
- 未知 | 30320次下载 | 免费
- 7Multisim 10下载Multisim 10 中文版
- 0.00 MB | 28588次下载 | 免费
- 8开关电源设计实例指南
- 未知 | 21539次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935053次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537793次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420026次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191183次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183277次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138039次下载 | 免费
评论
查看更多