电子发烧友App
创作
发文章
发帖 
提问 
发资料
发视频资料介绍
Table of Contents
AD7291 FMC-SDP Interposer & Evaluation Board / Xilinx KC705 Reference Design
Supported Devices
Evaluation Boards
Overview
This document presents the steps to setup an environment for using the EVAL-AD7291SDZ evaluation board together with the Xilinx KC705 FPGA board, the Xilinx Embedded Development Kit (EDK) and the Micrium µC-Probe run-time monitoring tool. Below is presented a picture of the EVAL-AD7291SDZ Evaluation Board with the Xilinx KC705 board.
For component evaluation and performance purposes, as opposed to quick prototyping, the user is directed to use the part evaluation setup. This consists of:
- 1. A controller board like the SDP-B ( EVAL-SDP-CS1Z)
- 2. The component SDP compatible product evaluation board
- 3. Corresponding PC software ( shipped with the product evaluation board)
The SDP-B controller board is part of Analog Devices System Demonstration Platform (SDP). It provides a high speed USB 2.0 connection from the PC to the component evaluation board. The PC runs the evaluation software. Each evaluation board, which is an SDP compatible daughter board, includes the necessary installation file required for performance testing.
Note: it is expected that the analog performance on the two platforms may differ.
Below is presented a picture of SDP-B Controller Board with the EVAL-AD7291SDZ Evaluation Board.
The EVAL-AD7291SDZ evaluation board is a member of a growing number of boards available for the SDP. It was designed to help customers evaluate performance or quickly prototype new AD7291 circuits and reduce design time. When using this evaluation board with the SDP board or BeMicro SDK board, apply +5 V, −5 V, and GND to Connector J2. VDRIVE is supplied by the SDP board or BeMicro SDK board, and VDD is supplied by an on-board regulator
The AD7291 is a 12-bit, low power, 8-channel, successive approximation analog-to-digital converter (ADC) with an internal temperature sensor.
The part operates from a single 3.3 V power supply and features an I2C-compatible interface. The part contains a 9-channel multiplexer and a track-and-hold amplifier than can handle frequencies up to 30 MHz. The device has an on-chip 2.5 V reference that can be disabled to allow the use of an external reference.
The AD7291 provides a 2-wire serial interface compatible with I2C interfaces. The I2C interface supports standard and fast I2C interface modes. The AD7291 normally remains in a partial power-down state while not converting and powers up for conversions. The conversion process can be controlled by a command mode where conversions occur across I2C write operations or an autocycle mode selected through software control. The AD7291 includes a high accuracy band gap temperature sensor, which is monitored and digitized by the 12-bit ADC to give a resolution of 0.25°C.
The AD7291 offers a programmable sequencer, which enables the selection of a preprogrammable sequence of channels for conversion.
More information
- AD7291 Product Info - pricing, samples, datasheet
Getting Started
The first objective is to ensure that you have all of the items needed and to install the software tools so that you are ready to create and run the evaluation project.
Required Hardware
- FMC-SDP adapter board
- EVAL-AD7291 evaluation board
Required Software
- Xilinx ISE 13.4 (Programmer (IMPACT) is sufficient for the demo and is available on Webpack).
- uC-Probe run-time monitoring tool
Downloads
The following table presents a short description the reference design archive contents.
| Folder | Description |
|---|---|
| Bit | Contains the KC705 configuration file that can be used to program the system for quick evaluation. |
| Microblaze | Contains the EDK 13.4 project for the Microblaze softcore that will be implemented in the KC705 FPGA. |
| Software | Contains the source files of the software project that will be run by the Microblaze processor. |
| uCProbeInterface | Contains the uCProbe interface and the .elf symbols file used by uC-Probe to access data from the Microbalze memory. |
Run the Demonstration Project
Hardware Setup
Before connecting the ADI evaluation board to the Xilinx KC705 make sure that the VADJ_FPGA voltage of the KC705 is set to 3.3V. For more details on how to change the setting for VADJ_FPGA visit the Xilinx KC705 product page.
- Use the FMC-SDP interposer to connect the ADI evaluation board to the Xilinx KC705 board on the FMC LPC connector.
- Connect the JTAG and UART cables to the KC705 and power up the FPGA board.
- Start IMPACT, and double click “Boundary Scan”. Right click and select Initialize Chain. The program should recognize the Kintex 7 device (see screenshot below).
- Program the KC705 FPGA using the “Bit/download.bit” file provided in the reference design archive.
- Power the ADI evaluation board.
At this point everything is set up and it is possible to start the evaluation of the ADI hardware through the controls in the uC-Probe application provided in the reference design.
Configure uC-Probe
Launch uC-Probe from the Start → All Programs → Micrium → uC-Probe.
Select uC-Probe options.
- Click on the uC-Probe icon on the top left portion of the screen.
- Click on the Options button to open the dialog box.
Set target board communication protocol as RS-232
- Click on the Communication tab icon on the top left portion of the dialog box
- Select the RS-232 option.
Setup RS-232 communication settings
- Select the RS-232 option from the Communication tab.
- Select the COM port to which the KC705 board is connected.
- Set the Baud Rate to 115200 bps.
- Press Apply and OK to exit the options menu.
Load and Run the Demonstration Project
- Click the Open option from the uC-Probe menu and select the .wsp file from the ucProbeInterface folder provided within the reference design files.
- Before opening the interface uC-Probe will ask for a symbols file that must be associated with the interface. Select the file ucProbeInterface/ADIEvalBoard.elf to be loaded as a symbol file.
- Run the demonstration project by pressing the Play button.
- In some cases it is possible that the uC-Probe interface will not respond to the commands the first time it is ran. In this situation just stop the interface by pressing the Stop button and run it again by pressing the Play button.
- After starting the uC-Probe interface wait until the status of the connection with the board displayed on the bottom of the screen is set to Connected. It is possible to use the interface only after the status is changed to Connected and the data transfer speed displayed next to the connection status is different than 0.
Demonstration Project User Interface
The following figure presents the uC-Probe interface that can be used for monitoring and controlling the operation of the EVAL-AD7291SDZ evaluation board.
Section A is used to activate the board and monitor activity. The communication with the board is activated / deactivated by toggling the ON/OFF switch. The Activity LED turns green when the communication is active. If the ON/OFF switch is set to ON and the Activity LED is BLACK it means that there is a communication problem with the board. See the Troubleshooting section for indications on how to fix the communication problems.
Section B is used to modify the content of Command Register. After any change of the buttons position is necessary to press the Write Command button.
Section C is used to read data from the VOLTAGE and T_SENSE registers. The T_SENSE value is converted and displayed as a value in degrees Celsius.
Section D is used to read data from the VOLTAGE_ALERT_STATUS and T_ALERT_STATUS registers.
Section E is used to modify the Alert Limits' values. After any change of the sliders position is necessary to press the Write Alert Limits button.
Troubleshooting
In case there is a communication problem with the board the follwing actions can be perfomed in order to try to fix the issues:
- Check that the evaluation board is powered as instructed in the board's user guide.
- In uC-Probe refresh the symbols file by right-clicking on the System Browser window and selecting Refresh Symbols.
- If the communication problem persists even after performing the previous steps, restart the uC-Probe application and try to run the interface again.
More information
- Example questions:
- An error occurred while fetching this feed: http://ez.analog.com/community/feeds/allcontent/atom?community=2061
- AD7656-1 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7658-1 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD9833 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD5780 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD5684R FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD5449 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- CN0204 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- CN0271 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7980 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD9838 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7988-1 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD5443 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7298 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD5757 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7683 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- 使用Xilinx FPGA实现OFDM系统 850次阅读
- 系统演示平台简化了从评估到原型设计的过渡 646次阅读
- Xilinx FPGA的FMC介绍 5643次阅读
- dfrobot可插拔传感器转接器简介 1043次阅读
- dfrobotWiiChuck转接器简介 1104次阅读
- 飞凌嵌入式JTAG转接板介绍 1614次阅读
- digilent FMC Pcam适配器介绍 2731次阅读
- digilent FMC-HDMI：双HDMI输入扩展子板介绍 4286次阅读
- 天嵌科技LVDS转接板-TTL-LVDS转接板规格 3772次阅读
- 2.5 GSPS高性能数模转换器——AD9739A DAC 4675次阅读
- 关于FPGA的FMC接口的详细介绍 1.1w次阅读
- 系统演示平台便于快速进行原型制作与评估 1504次阅读
- Maxim为三款Xilinx FPGA参考设计提供电源管理方案 1163次阅读
- 非插入式器件如何测量？ 1573次阅读
- ADI实验室电路:500V共模电压电流监控器 2923次阅读
上传资料赚积分下载排行
本周
- 1电子电路原理第七版PDF电子教材免费下载
- 0.00 MB | 1491次下载 | 免费
- 2单片机典型实例介绍
- 18.19 MB | 95次下载 | 1 积分
- 3S7-200PLC编程实例详细资料
- 1.17 MB | 27次下载 | 1 积分
- 4笔记本电脑主板的元件识别和讲解说明
- 4.28 MB | 18次下载 | 4 积分
- 5开关电源原理及各功能电路详解
- 0.38 MB | 11次下载 | 免费
- 6100W短波放大电路图
- 0.05 MB | 4次下载 | 3 积分
- 7基于单片机和 SG3525的程控开关电源设计
- 0.23 MB | 4次下载 | 免费
- 8基于AT89C2051/4051单片机编程器的实验
- 0.11 MB | 4次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 2PADS 9.0 2009最新版 -下载
- 0.00 MB | 66304次下载 | 免费
- 3protel99下载protel99软件下载(中文版)
- 0.00 MB | 51209次下载 | 免费
- 4LabView 8.0 专业版下载 (3CD完整版)
- 0.00 MB | 51043次下载 | 免费
- 5555集成电路应用800例(新编版)
- 0.00 MB | 33562次下载 | 免费
- 6接口电路图大全
- 未知 | 30320次下载 | 免费
- 7Multisim 10下载Multisim 10 中文版
- 0.00 MB | 28588次下载 | 免费
- 8开关电源设计实例指南
- 未知 | 21539次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935053次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537793次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420026次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191183次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183277次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138039次下载 | 免费
工商网监
评论