电子发烧友App
创作
发文章
发帖 
提问 
发资料
发视频资料介绍
Table of Contents
AD5781 - No-OS Driver for Microchip Microcontroller Platforms
Supported Devices
Evaluation Boards
- PmodDA5
Overview
The AD5781 is a single 18-bit, unbuffered voltage-output DAC that operates from a bipolar supply of up to 33 V. The AD5781 accepts a positive reference input in the range 5V to VDD – 2.5 V and a negative reference input in the range VSS + 2.5 V to 0 V. The AD5781 offers a relative accuracy specification of ±0.5 LSB max, and operation is guaranteed monotonic with a ±0.5 LSB DNL max specification.
The part uses a versatile 3-wire serial interface that operates at clock rates up to 35 MHz and that is compatible with standard SPI®, QSPI™, MICROWIRE™, and DSP interface standards. The part incorporates a power-on reset circuit that ensures the DAC output powers up to 0 V and in a known output impedance state and remains in this state until a valid write to the device takes place. The part provides an output clamp feature that places the output in a defined load state.
Applications
- Medical Instrumentation
- Test and Measurement
- Industrial Control
- Scientific and Aerospace Instrumentation
- Data Acquisition Systems
- Digital Gain and Offset Adjustment
- Power Supply Control
The goal of this project (Microcontroller No-OS) is to be able to provide reference projects for lower end processors, which can't run Linux, or aren't running a specific operating system, to help those customers using microcontrollers with ADI parts. Here you can find a generic driver which can be used as a base for any microcontroller platform and also specific drivers for different microcontroller platforms.
Driver Description
The driver contains two parts:
- The driver for the AD5781 part, which may be used, without modifications, with any microcontroller.
- The Communication Driver, where the specific communication functions for the desired type of processor and communication protocol have to be implemented. This driver implements the communication with the device and hides the actual details of the communication protocol to the ADI driver.
The Communication Driver has a standard interface, so the AD5781 driver can be used exactly as it is provided.
There are three functions which are called by the AD5781 driver:
- SPI_Init() – initializes the communication peripheral.
- SPI_Write() – writes data to the device.
- SPI_Read() – reads data from the device.
SPI driver architecture
The following functions are implemented in this version of AD5781 driver:
| Function | Description |
|---|---|
| long AD5781_Init(void) | Initializes the communication with the device. Return 0 in case of success and negative error code otherwise. |
| long AD5781_SetRegisterValue(unsigned char registerAddress, unsigned long registerValue) | Writes data into a register. Receives as parameters the address of the register and the value of the register. Returns 0 in case of success or negative error code. |
| long AD5781_GetRegisterValue(unsigned char registerAddress) | Reads the value of a register. Receives as parameter the address of the register. Returns the value of the register or negative error code. |
| long AD5781_DacOuputState(unsigned char state) | Sets the DAC output in one of the three states(normal, clamped via 6KOhm to GND, tristate). Returns negative error code or 0 in case of success. |
| long AD5781_SetDacValue(unsigned long value) | Writes to the DAC register. Receives as parameter the value to be written to DAC. Returns negative error code or 0 in case of success. |
| long AD5781_SoftInstruction(unsigned char instructionBit) | Asserts RESET, CLR or LDAC in a software manner. Receives as parameter one of the software control bits(RESET, CLR or LDAC). Returns negative error code or 0 in case of success. |
| long AD5781_Setup(unsigned long setupWord) | Configures the output amplifier, DAC coding, SDO state and the linearity error compensation. Receives as parameter a 24-bit value that sets or clears the Control Register bits(RBUF, BIN/2sC, SDODIS, LINCOMP). Returns negative error code or 0 in case of success. |
HW Platform(s):
Downloads
- PmodDA5 Demo for PIC32MX320F128H: https://github.com/analogdevicesinc/no-OS/tree/master/Microchip/PIC32MX320F128H/PmodDA5
- PIC32MX320F128H Common Drivers: https://github.com/analogdevicesinc/no-OS/tree/master/Microchip/PIC32MX320F128H/Common
Digilent Cerebot MX3cK Quick Start Guide
This section contains a description of the steps required to run the AD7303 demonstration project on a Digilent Cerebot MX3cK platform.
Required Hardware
- PmodDA5
Required Software
- The AD5781 demonstration project for PIC32MX320F128H.
The AD5781 demonstration project for PIC32MX320F128H consists of three parts: the AD5781 Driver, the PmodDA5 Demo for PIC32MX320F128H and the PIC32MX320F128H Common Drivers.
All three parts have to be downloaded.
Hardware Setup
A PmodDA5 has to be connected to the JE connector of Cerebot MX3cK development board.
Reference Project Overview
The following commands were implemented in this version of AD5781 reference project for Cerebot MX3cK board.
| Command | Description |
|---|---|
| help? | Displays all available commands. |
| reset! | Resets the AD5781 device. |
| coding= | Selects the coding style. Accepted values: 0 - Offset binary coding. 1 - Two's complement coding.(default) |
| coding? | Display the current coding style. |
| register= | Writes to the DAC register. Accepted values: 0 .. 262143 - the value written to the DAC. |
| register? | Displays last written value to the DAC register. |
| voltage= | Sets the DAC output voltage. Accepted values: -10 .. +10 - desired output voltage in volts. |
| voltage? | Displays the output voltage. |
| output= | Selects the DAC output state. Accepted values: 0 - Normal state. 1 - Clamped via 6KOhm to AGND. 2 - Tristate.(default) |
| output? | Displays the DAC output state. |
| rbuf= | Sets/resets the RBUF bit from control register. Accepted values: 0 - RBUF is reset. 1 - RBUF is set.(default) |
| rbuf? | Displays the value of RBUF bit from control register. |
Commands can be executed using a serial terminal connected to the UART1 peripheral of PIC32MX320F128H.
The following image shows a generic list of commands in a serial terminal connected to processor’s UART peripheral.
Software Project Setup
This section presents the steps for developing a software application that will run on the Digilent Cerebot MX3cK development board for controlling and monitoring the operation of the ADI part.
- Run the MPLAB X integrated development environment.
- Choose to create a new project.
- In the Choose Project window select Microchip Embedded category, Standalone Project and press Next.
- In the Select Device window choose PIC32MX320F128H device and press Next.
- In the Select Tool window select the desired hardware tool and press Next.
- In the Select Compiler window chose the XC32 compiler and press Next.
- In the Select Project Name and Folder window choose a name and a location for the project.
- After the project is created, all the downloaded source files have to be copied in the project folder and included in the project.
- The project is ready to be built and downloaded on the development board.
More information
- Example questions:
- An error occurred while fetching this feed: http://ez.analog.com/community/feeds/allcontent/atom?community=2077
- AD5933-适用于微芯片微控制器平台的无操作系统驱动程序
- AD5160-适用于瑞萨微控制器平台的无操作系统驱动程序
- AD5160-适用于微芯片微控制器平台的无操作系统驱动程序
- AD7193-适用于瑞萨微控制器平台的无操作系统驱动程序
- AD5628-适用于微芯片微控制器平台的无操作系统驱动程序
- AD5541A-适用于瑞萨微控制器平台的无操作系统驱动程序
- AD5933-瑞萨微控制器平台的无操作系统驱动程序
- AD7780-适用于单片机平台的无操作系统驱动程序
- AD5781-适用于瑞萨微控制器平台的无操作系统驱动程序
- AD74xx-适用于微芯片微控制器平台的无操作系统驱动程序
- AD799x-适用于微芯片微控制器平台的无操作系统驱动程序
- AD7980-适用于微芯片微控制器平台的无操作系统驱动程序
- AD799x-用于瑞萨微控制器平台的无操作系统驱动程序
- AD5541A-适用于微芯片微控制器平台的无操作系统驱动程序
- AD7156-适用于瑞萨微控制器平台的无操作系统驱动程序
- 实时时钟为微控制器系统增加了精确的计时功能 1121次阅读
- 了解和使用无操作系统和平台驱动程序 1066次阅读
- 基于具有USB功能的STM32微控制器 3682次阅读
- 基于MC68VZ328微处理器和ADS7843芯片实现触摸屏驱动系统的设计 6030次阅读
- 微控制器的主要应用在哪里 8647次阅读
- 基于一种适用于模拟脉宽调制PWM可调光的LED驱动器NCL2801解析 5524次阅读
- 嵌入式Linux内核的驱动程序开发是怎样的 1415次阅读
- 适用于测控领域的4种实时操作系统对比分析 3531次阅读
- 浅谈电脑驱动程序的工作原理 详解电脑驱动程序意义 2.9w次阅读
- 基于嵌入式Linux内核的系统设备驱动程序开发设计 1113次阅读
- 基于Linux2.6.30开发DS18B20的驱动程序的类型和文件操作接口函数详解 1377次阅读
- 基于STM32的数字PDA系统软件系统设计 1480次阅读
- 8155驱动程序 3057次阅读
- 基于STM32ZET6控制器的数字PDA系统的设计 1504次阅读
- Silicon Labs 32 位微控制器的 10 大技术特点 1222次阅读
上传资料赚积分下载排行
本周
- 1电子电路原理第七版PDF电子教材免费下载
- 0.00 MB | 1491次下载 | 免费
- 2单片机典型实例介绍
- 18.19 MB | 95次下载 | 1 积分
- 3S7-200PLC编程实例详细资料
- 1.17 MB | 27次下载 | 1 积分
- 4笔记本电脑主板的元件识别和讲解说明
- 4.28 MB | 18次下载 | 4 积分
- 5开关电源原理及各功能电路详解
- 0.38 MB | 11次下载 | 免费
- 6100W短波放大电路图
- 0.05 MB | 4次下载 | 3 积分
- 7基于单片机和 SG3525的程控开关电源设计
- 0.23 MB | 4次下载 | 免费
- 8基于AT89C2051/4051单片机编程器的实验
- 0.11 MB | 4次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 2PADS 9.0 2009最新版 -下载
- 0.00 MB | 66304次下载 | 免费
- 3protel99下载protel99软件下载(中文版)
- 0.00 MB | 51209次下载 | 免费
- 4LabView 8.0 专业版下载 (3CD完整版)
- 0.00 MB | 51043次下载 | 免费
- 5555集成电路应用800例(新编版)
- 0.00 MB | 33562次下载 | 免费
- 6接口电路图大全
- 未知 | 30320次下载 | 免费
- 7Multisim 10下载Multisim 10 中文版
- 0.00 MB | 28588次下载 | 免费
- 8开关电源设计实例指南
- 未知 | 21539次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935053次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537793次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420026次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191183次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183277次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138039次下载 | 免费
工商网监
评论